habilitar el USB en ct 536+

ZoNeR@ Registrado: Oct 31, 2011 Mensajes: 3

Hola a todos.
Tengo modificado el hardware del ct-536+, le he metido el openwrt y lo tengo conectado a otro hg-536. Tengo acceso a internet y en principio todo el apaño funciona correctamente. mi intención es compartir un hd en red. para ello tengo conectado un hdd externo dividido en tres particiones ( no se si esto influira). La primera son unos 90gb en fat. la cuestión es que no consigo "ver" el contenido de dicha partición.
Los pasos que sigo son los siguientes:
-enciendo el hdd
-lo conecto al router(openwrt) apagado
-enciendo el router
-desde telnet entro en el router y utilizo el comando "ls -lh /dev/sd*"
la respuesta es que no existe nada ahí.

Tengo instalados los paquetes que se mencionan en el anterior comentario:
- kmod-usb-core
- kmod-usb-ohci
- kmod-fs-vfat
- kmod-usb-storage-extras
- block-mount
- usbutils

La verdad que no se ni como utilizar todo esto.

El "dmesg" y el "lsusb" me muestran esto:

BusyBox v1.15.3 (2010-03-28 21:16:56 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
BackFire (10.03-rc3, r20642) ----------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/# ls -lh /dev/sd*
ls: /dev/sd*: No such file or directory
root@OpenWrt:/# lsusb
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
root@OpenWrt:/# dmesg
Linux version 2.6.32.10 (openwrt@wrt1.marcant.net) (gcc version 4.3.3 (GCC) ) #8
Thu Apr 1 10:20:02 CEST 2010
Detected Broadcom 0x6348 CPU revision a2
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-5.17
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: 96348GW-11
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 802981a0, node_mem_map 802df000
Normal zone: 32 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd cons
ole=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13300k/16384k available (2135k kernel code, 3084k reserved, 458k data, 1
40k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x001fff]
pci 0000:01:1e.0: CardBus bridge, secondary bus 0000:02
pci 0000:01:1e.0: IO window: 0x8008000-0x80080ff
pci 0000:01:1e.0: IO window: 0x8008400-0x80084ff
pci 0000:01:1e.0: MEM window: 0x38000000-0x3fffffff
PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:01:1e.0 to 64
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.262:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
msgmni has been set to 25
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6, board type 96348GW-11, and ta
gid bc300.
bcm963xx_flash: Partition 0 is CFE offset 80c73a20 and length 0
bcm963xx_flash: Partition 1 is kernel offset f34 and length 0
bcm963xx_flash: Partition 2 is rootfs offset f75 and length 0
bcm963xx_flash: Partition 3 is nvram offset fb6 and length 0
bcm963xx_flash: Partition 4 is linux offset ff6 and length 0
bcm963xx_flash: Spare partition is 2a0000 offset and length 150000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be s
maller than an erase block -- forcing read-only
0x0000000f0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2A0000, len=150000
0x0000002a0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl-fail
Registered led device: ppp
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 140k freed
Please be patient, while OpenWrt loads ...
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new device driver usb
b43-phy0: Broadcom 4306 WLAN found (core revision 5)
phy0: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NTFS driver 2.1.29 [Flags: R/O MODULE].
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (210 buckets, 840 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new full speed USB device using bcm63xx_ohci and address 2
usb 1-1: device descriptor read/64, error -62
usb 1-1: device descriptor read/64, error -62
usb 1-1: new full speed USB device using bcm63xx_ohci and address 3
usb 1-1: device descriptor read/64, error -62
usb 1-1: device descriptor read/64, error -62
usb 1-1: new full speed USB device using bcm63xx_ohci and address 4
usb 1-1: device not accepting address 4, error -62
usb 1-1: new full speed USB device using bcm63xx_ohci and address 5
usb 1-1: device not accepting address 5, error -62
hub 1-0:1.0: unable to enumerate USB device on port 1
b43 ssb0:0: firmware: requesting b43/ucode5.fw
b43 ssb0:0: firmware: requesting b43/pcm5.fw
b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw
b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state

¿cómo lo veis?
Gracias!

ZoNeR@ Registrado: Oct 31, 2011 Mensajes: 3

ya esta. ya me detecta el usb perfectamente. ahora.... alguien podria darme algunas indicaciones de como conectar el hdd en red?
Gracias!

Invitado

Hola,

Si te lo detecta, puedes montarlo y puedes leer y escribir, en los siguientes enlaces tienes información:
- Instalación: http://wiki.openwrt.org/doc/howto/cifs.server
- Configuración: http://wiki.openwrt.org/doc/uci/samba

Si te lías con linux puedes probar primero con:

opkg update;opkg install samba3;opkg install luci-app-samba

Ésta última es para configurarlo desde la interfaz web. No funciona con la rc5 (Creo que por problema de uhttp no de este paquete), con la última rc6 no lo he probado (pero imagino que sí), y con la que tienes tú no tengo ni idea.

P.D: No te olvides de instalar "block-hotplug" si tienes espacio para no tener que estar siguiendo el ritual de encendido y apagado cada vez que, por lo que sea, tengas que desconectar el disco.

Invitado

Cita:

...Ésta última es para configurarlo desde la interfaz web. No funciona con la rc5 (Creo que por problema de uhttp no de este paquete), con la última rc6 no lo he probado (pero imagino que sí), y con la que tienes tú no tengo ni idea.
...

Con la " Backfire (10.03.1-RC6, r28680) ", funciona perfectamente.

Un saludo.